Tips On How To Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was created by two guys in California. They wanted to develop a cool writing instrument that appeared as if a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.
The Smok Pen includes a built quality that’s just great. I found that even though it can be an electronic pen the construction is simply as good as the pens that I have reviewed. Simply because of how they made the most notable cap. You don’t have to worry about the cap cracking or breaking on you Smok Valve Pen.
The two biggest differences that separate the Smok Valve from other pens is the form of the coils and just how that they are built. Generally the coil on a Smok Pen is larger than on other pens. I believe that they did this on purpose, to make the pen feel more substantial.
If you take a glance at a Smok Pen, you will observe that the body of the pen is round rather than smooth like other pens. On the back of the pen there exists a little tab that houses the coil. Once you press on the tab Novo 2 you can actually turn the heating element on / off. I really liked this feature because it allows me to utilize the Smok Pen 22 whenever I feel like smoking.
To use the Smok Pen you should keep the heat button pressed. After the button is pressed, the heating element will start to warm up. Once it reaches the appropriate temperature it is possible to turn off the heating element. Smok recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.
Once you put your Smok Pen in to the tank you will see a indicator light come on. The indicator light will remain green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen in to the charger before you apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids into the coil heads.
Once you have completed this step, you should always check to see in case you are at the right temperature for the coils to fire. Or even then you should turn the power off and try again. For anyone who is still not satisfied together with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just do not work as they should. I would recommend that you perform the next two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.
Prior to going any further you should take away the battery from your pen and unscrew the magnetic cap. You need to then take away the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. When you have loosened this wire after that you can access the sub-ohm. You should then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.
When you have placed the sub-ohm tank in to the pen you should then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the power and follow the on screen instructions. You need to place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you first put the pen into the microwave the electronic reading will show a low voltage protection setting. If this setting will not automatically get set then you should follow the on screen instructions.
Once the Smok Pen has reached the temperature that it needs to reach you should then connect the two wires to the negative and positive on the positive post on the Smok unit. You need to then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step is to connect the positive cable to the bottom of the Smok’s power switch.
After all the components have been placed into the pen, you should turn the power on. After the first test run, you ought to be able to see the battery life indicator light seriously. If you do not see any sign of life from the Smok Pen, you need to take away the battery from the pen and then replace it with a fresh one. For your convenience there is also a green light that can be pressed as a way to confirm the battery charging status. Once you have done these things and you do not start to see the green light indicating charging, you should replace the battery.